Paver Walkway Cost Calculator
As of 2026, a paver walkway costs $8–22 per square foot installed with concrete pavers. A 4×30 ft front walk runs $960–2,650; a 3×20 garden path runs $480–1,300. Enter your walkway length, width and material to get the installed cost and full material list.
Last updated: October 10, 2026
Your project
Pro Tips
- A narrow path needs far more edge restraint per square foot than a patio.
- Curves add about 5% more pavers for cuts.
- Make a front walk at least 4 ft wide so two people can walk side by side.
- Breaking out an old concrete walk adds $2–6 per square foot.
- Slope the path slightly to one side so water runs off.
Installed cost
$960–2,650
$8–22 per sq ft · typical $1,680
120 sq ft · Concrete pavers
Get your material list →Materials
$720–1,850
what you'd pay for DIY
Labor (est.)
$290–790
installed minus materials
| Plain concrete | $6–12/sq ft | $720–1,450 |
| Exposed aggregate concrete | $8–16/sq ft | $960–1,900 |
| Concrete pavers | $8–22/sq ft | $960–2,650 |
| Stamped concrete | $8–28/sq ft | $960–3,350 |
| Clay brick pavers | $12–26/sq ft | $1,450–3,100 |
| Travertine pavers | $15–27/sq ft | $1,800–3,250 |
| Flagstone (dry-laid) | $15–32/sq ft | $1,800–3,850 |
| Porcelain pavers | $16–35/sq ft | $1,900–4,200 |
| Flagstone (mortared) | $20–45/sq ft | $2,400–5,400 |
Full material list
Pavers
336
6 × 9 in, +5%
Base gravel
2.7 tons
4 in compacted
Bedding sand
0.5 tons
1 in layer
Polymeric sand
2 bags
50 lb
Edge restraint
68 ft
DIY materials
$720–1,850
installed: $960–2,650
Based on 2026 U.S. installed-cost data. See methodology.
For the full background, read our complete walkway guide and flagstone vs concrete walkway comparison.
Paver Walkway Cost by Size
Walkways are priced by area, so length times width drives the total. These are installed prices for concrete pavers at the U.S. average of $8–22 per square foot, on bare ground.
| Size | Area | Installed cost |
|---|---|---|
| 20 × 3 ft | 60 sq ft | $480–1,300 |
| 20 × 4 ft | 80 sq ft | $640–1,750 |
| 30 × 4 ft | 120 sq ft | $960–2,650 |
| 40 × 4 ft | 160 sq ft | $1,300–3,500 |
| 50 × 5 ft | 250 sq ft | $2,000–5,500 |
A long 5×50 ft walk comes to about $2,000–5,500. The calculator uses a flat national rate per square foot; quotes for very short paths often carry a minimum charge, because a crew's setup and delivery don't shrink with the area.
Standard Walkway Widths and What They Cost
A garden or side path is typically 3 ft wide. A front walk is usually 4 ft, wide enough for two people side by side, and a grand entry walk can be 5 ft or more. Each extra foot of width adds area along the whole length:
| Size | Area | Installed cost |
|---|---|---|
| 30 × 3 ft | 90 sq ft | $720–2,000 |
| 30 × 4 ft | 120 sq ft | $960–2,650 |
| 30 × 5 ft | 150 sq ft | $1,200–3,300 |
| 30 × 6 ft | 180 sq ft | $1,450–3,950 |
Match the walk to the door and the scale of the house rather than going as narrow as possible. Our complete walkway guide covers layout and proportions.
Walkway Materials Compared
For the same 4×30 ft path (120 sq ft), installed prices by material, cheapest first:
| Material | Installed per sq ft | 30 × 4 ft total |
|---|---|---|
| Plain concrete | $6–12 | $720–1,450 |
| Exposed aggregate concrete | $8–16 | $960–1,900 |
| Concrete pavers | $8–22 | $960–2,650 |
| Stamped concrete | $8–28 | $960–3,350 |
| Clay brick pavers | $12–26 | $1,450–3,100 |
| Travertine pavers | $15–27 | $1,800–3,250 |
| Flagstone (dry-laid) | $15–32 | $1,800–3,850 |
| Porcelain pavers | $16–35 | $1,900–4,200 |
Plain concrete is cheapest at about $720–1,450. Clay brick ($1,450–3,100) is the classic front-walk look, and dry-laid flagstone ($1,800–3,850) suits informal garden paths. For poured walks, see our concrete walkway cost guide and flagstone vs concrete walkway comparison. Compare patio-sized areas with the patio cost calculator.
Why Edge Restraint Matters More on a Walkway
A walkway is all edge. A 4×30 ft path needs about 68 linear feet of edge restraint for 120 sq ft, roughly 57 ft per 100 sq ft. A 12×16 patio needs 56 ft for 192 sq ft, or 29 ft per 100 sq ft.
| Size | Pavers | Base | Sand | Poly bags | Edging |
|---|---|---|---|---|---|
| 20 × 3 ft | 168 | 1.3 t | 0.3 t | 1 | 46 ft |
| 30 × 4 ft | 336 | 2.7 t | 0.5 t | 2 | 68 ft |
| 50 × 5 ft | 700 | 5.6 t | 1 t | 4 | 110 ft |
Without a solid edge, the outer rows of a narrow path drift sideways and the joints open up. Ask installers to spike edging along both sides, not just to rely on soil. The table also shows pavers, base, sand and polymeric sand for each size. Get exact numbers from the paver base calculator and polymeric sand calculator.
Curved Paver Walkway Cost
Curves look better on a winding garden path but need more cuts along both edges. The calculator adds 5% extra waste for a curved layout, so a 4×30 ft walk goes from 336 to 352 pavers, and the material cost rises from $720–1,850 to $740–1,900.
| Size | Area | Pavers needed |
|---|---|---|
| 20 × 4 ft | 80 sq ft | 235 |
| 30 × 4 ft | 120 sq ft | 352 |
| 40 × 4 ft | 160 sq ft | 470 |
Expect installers to quote extra cutting time for tight curves on top of the installed rate. Browse curved walkway ideas for shapes that keep cuts manageable.
Paver Walkway Patterns and Waste
The laying pattern changes how many pavers you buy. Running bond, the simplest pattern, needs about 5% extra for cuts. Basketweave needs about 7% and 45° herringbone about 15%, because every edge piece is cut at an angle. On a narrow walk, edges make up a large share of the pavers, so pattern choice matters more than on a patio.
| Size | Area | Pavers needed |
|---|---|---|
| 20 × 4 ft | 80 sq ft | 246 |
| 30 × 4 ft | 120 sq ft | 368 |
| 40 × 4 ft | 160 sq ft | 491 |
That table shows herringbone counts. A 4×30 ft walk in herringbone needs 368 pavers against 336 in running bond. Herringbone also locks together best under foot traffic, which is why it's common on busy front walks. See walkway patterns for layout ideas.
Front Walk vs. Garden Path
A front walk carries daily foot traffic, deliveries and guests, so it is usually wider, set on a full compacted base and laid in a formal pattern. A backyard or garden path can be narrower and more relaxed, often dry-laid flagstone or stepping stones. A 3×20 ft garden path compares like this:
| Material | Installed per sq ft | 20 × 3 ft total |
|---|---|---|
| Concrete pavers | $8–22 | $480–1,300 |
| Clay brick pavers | $12–26 | $720–1,550 |
| Flagstone (dry-laid) | $15–32 | $900–1,900 |
See front walkway ideas, backyard walkway ideas and stepping stone walkway ideas for designs.
Paver Walkway Cost by Region
Labor rates move walkway prices the most from region to region. A 4×30 ft paver walk by region:
| Region | Multiplier | 30 × 4 ft installed |
|---|---|---|
| U.S. average | ×1.00 | $960–2,650 |
| Northeast | ×1.10 | $1,050–2,900 |
| Pacific / West Coast | ×1.18 | $1,150–3,100 |
| Midwest | ×1.00 | $960–2,650 |
| South | ×0.90 | $860–2,400 |
| Mountain / Southwest | ×1.00 | $960–2,650 |
The West Coast runs about ×1.18 the national average and the South about ×0.90. These are broad averages, not ZIP-level quotes. Because walkways are small jobs, a crew's minimum charge and travel time weigh more heavily than on a patio, so quotes in expensive metro areas can land above the table. Set your region in the calculator above to adjust the estimate.
Replacing an Old Concrete Walkway with Pavers
Breaking out and hauling away an old concrete walk adds $2–6 per square foot. A 4×30 ft replacement comes to about $1,200–3,350, against $960–2,650 on bare ground.
| Size | Area | Installed cost |
|---|---|---|
| 20 × 3 ft | 60 sq ft | $600–1,700 |
| 30 × 4 ft | 120 sq ft | $1,200–3,350 |
| 40 × 4 ft | 160 sq ft | $1,600–4,500 |
| 50 × 5 ft | 250 sq ft | $2,500–7,000 |
Ask whether the quote includes cutting the old walk back cleanly where it meets steps, a driveway or a porch slab, and whether any existing base can be reused after inspection. If the old walk is sound and only looks tired, resurfacing or staining may cost less. See stained concrete walkway ideas.
DIY Paver Walkway: Materials vs. Labor
A straight walkway on flat ground is one of the most DIY-friendly paving jobs. If you do it yourself, the materials column is your budget:
| Size | Materials (DIY) | Labor (est.) | Installed total |
|---|---|---|---|
| 20 × 3 ft | $430–1,100 | $140–400 | $480–1,300 |
| 30 × 4 ft | $720–1,850 | $290–790 | $960–2,650 |
| 50 × 5 ft | $1,300–3,450 | $750–2,050 | $2,000–5,500 |
Add a plate compactor and saw rental. The hard parts are the same as on a patio: digging to an even depth, compacting the base in thin lifts and keeping a slight cross slope so water sheds. A walk that meets steps or a driveway needs careful height matching, which is a good reason to hire out the tricky ends even if you lay the run yourself. Build your shopping list with the paver calculator, and see the paver installation cost calculator for what installers charge for each step. More walkway designs are on our walkway ideas page.